Seagate freeagent dockstar debian install#
Seagate freeagent dockstar debian upgrade#
Seagate freeagent dockstar debian software#
Seagate freeagent dockstar debian download#
Seagate freeagent dockstar debian mac#

In addition to installing a new bootloader, the script corrects several minor errors on the factory-installed system. When it asked me if I wanted to disable the pogoplug services, I chose “Yes”. I read the prompts and answered the questions affirmatively. The following instructions are copied directly from the Official Plugbox Linux Installation : cd /tmp This will replace the bootloader in /dev/mtd0 with a new one.

Seagate freeagent dockstar debian download#

Download and run the bootloader installation script.

Ssh to the Dockstar and log in as root.

Seagate freeagent dockstar debian install#

The first thing to do is to install a bootloader that will try booting from USB before it boots from ROM. This is where I switched gears and followed the Official Plugbox Linux Installation.

Seagate freeagent dockstar debian software#

That stops the ‘phone home software from starting at boot time.Īssuming all went well (and that I have my facts straight), it should now be safe to connect the device to a network that has Internet connectivity. # nohup $INSTDIR/bin/hbwd $INSTDIR/bin/hbplug > /dev/null 2>&1 &

Comment out the following lines (as shown):.

Edit /usr/local/cloudengines/bin/hbplug_init.

Here’s where I start to diverge from Alexander Holler’s instructions.

Remount the root file system read/write.

Stop the Dockstar’s ‘phone home software.Copy the image files and associated md5 hashes to a safe storage location.Then remove the USB drive and power cycle the Dockstar to start it up again. I used the following script: for f in 0 1 2 3 The Dockstar should detect when it is plugged in, and mount it in a subdirectory of /tmp/.cemt/.Ĭhange directory to the USB-mounted file system, making sure it’s the right partition on the right device. Ext2 and VFat (and probably a few others) are supported. Once again, I was guided by Using Linux on a DockStar (How to brick your DockStar and void the warranty).Ī memory stick or hard drive will do. Personally, I am paranoid so I created the backup. Configure the GigE interface with an address on the same network as the Dockstar’s.We’ll use 169.254.11.12 for the remaining examples. You can find this number on the underside of the device.

Seagate freeagent dockstar debian mac#

It will be .n, where m and n are the last two octets of the Ethernet MAC address of the Dockstar.

Figure out the IP address of the Dockstar.

No worries, since the laptop was not forwarding packets so the Dockstar could not ‘phone home. I used a laptop and I did, in fact, allow the laptop to connect to the Internet using its Wireless NIC. Two computers can be directly connected with a standard cable. Why a GigE Ethernet port? Because GigE is auto-sensing and does not need a crossover cable or switch.

Connect the Dockstar’s Ethernet port to the GigE Ethernet port of a stand-alone computer.

Seagate freeagent dockstar debian upgrade#

Once that upgrade is installed, it will become much more difficult to gain access to the Dockstar. Why? Because the first thing it will do is attempt to connect to an external site to download a firmware upgrade, which it will then install. Do not let the Dockstar connect to the Internet.I learned this part from reading Using Linux on a DockStar (How to brick your DockStar and void the warranty), by Alexander Holler Step 1: Safely boot and access the Dockstar If you follow these steps, you do so at your own risk.Following these steps will void your warranty and, should something go wrong, could turn your Dockstar into a pointless plastic paperweight.I am not telling you to do any of this, I’m just telling you what I did.Thanks to Kai Blin for getting me started with these devices. There are references included that provide more details for those who are interested. Here are the steps I took to take charge of my Dockstar. These days, if you can still find them, the price is likely to be US$70 and up. Once news got out that these things could be so easily re-purposed, they started selling like crazy. I run a bzflag server on one of them, and they can run Samba too. I’m using them for testing and as small home servers. Back in December of 2010, the price of these had dropped to around US$30.00 each including shipping, so I picked up four four of them. It is quite easy to reflash the ROM so that it boots Linux from a USB device. The Seagate FreeAgent Dockstar is a small ARM-based embedded computer based on the Marvell Sheevaplug design. Seagate Freeagent Dockstar, showing side vents, three USB ports, the GigE port, and the power connector hole.